THIS IS NOT THE SAME PAGE YOU JUST VIEWED. KEEP SCROLLING DOWN.

Replacement Pioneer RT-909 Reel-to-Reel tape deck Rubber Pinch Rollers:   These are fresh rollers with new rubber and new brass bushings for your Pioneer RT-909 / RT-901 Reel to Reel Deck. If yours have never been replaced or are over 8-12 years old, it's time. If your pinch-rollers are causing mis-tracking, slipping, excessive Wow & Flutter, are "gummy", cracked, glazed hard, have rounded-off edges or disintegrating and your belt has turned to "tar", then here you go! Breathe new life into your classic Pioneer RT-909 RT-901 tape recorder. Our kit comes with a new, fresh belt, and VERY legible / HIGH QUALITY graphics of the applicable Pioneer service manual sections, with additional, abbreviated instructions. These are now discontinued from Pioneer, so get them while you can. We currently have only a few back in stock to sell (the rest we're keeping for our decks. Sorry they will not fit the Pioneer RT-707. Only the Pioneer RT909 & the RT901. For Pioneer RT-707 Rubber Pinch rollers, click here...)   Domestic US Customers   International Customers PRICE INCLUDES: A pair of replacement, NEW Pioneer RT-909 Reel-to-Reel tape deck Pinch Rollers SHIPPING   Free NEW Main Drive Belt Your Price $98.99 (includes shipping to any of the US states) PRICE INCLUDES: A pair of replacement, NEW Pioneer RT-909 Reel-to-Reel tape deck Pinch Rollers SHIPPING   Free NEW Main Drive Belt Your Price $106.99 (includes Airmail shipping to any other worldwide location)   IF YOU PREFER TO PLACE YOUR ORDER BY PHONE, PLEASE CALL US AT: 719-964-7205 *NOT INCLUDED IN ANY OTHER COMBINED PARTS DISCOUNTS OR SALES (sorry, we do not have, nor can give out any instructions or advice on the actual repair procedures)

NEW LISTING 3/24/07 (Click on above thumbnails to enlarge photos) PIONEER MODEL RT-909 RT909 (#1) REEL TO REEL PARTS PARTING OUT Many parts will also work on the RT-901 RT901 Parting out a clean Pioneer RT-909 Reel-Reel Deck. Everything runs and looks great! This one has an issue in that when it was powered up, the Fast Rewind motor always turned. Heads in like new condition. Hubs run perfectly true! All motors run fine, fast, smooth and quiet. All transport functions work well. Internal boards will need trim pots adjusted when installed in new deck. Cosmetics like new! We're parting it out as we've had so many requests for parts. Some RT-909 parts may also fit RT-901's, but we have no cross reference info.  Motors, Heads, Circuit Boards, Knobs, Pots, Controls, Switches, Rollers, Spindles, Face Etc. PIONEER RT-909 RT909 - Face Plate, Upper Main (Does not include screws or screw bezels )- Clean and never been rack mounted so screw holes are in "NEW" condition - $75. PIONEER RT-909 RT909 - Lower Face plate with Silk-Screening - Clean and never been rack mounted so screw holes are in "NEW" condition as well as the silk screening - $145. SOLD OUT PIONEER RT-909 RT909 - Capstan Motor - Part # RXM-062 (we have information that the Teac Em1446 / X-series motor is the same, but may need it's polarity reversed when connected. Just FYI.) - $105. SOLD OUT  Fast Wind / Hub / reel motor right or left Part # RXM-060 - $105. ea Capstan Flywheel (less nylon ball bearing) - $35. ea Capstan Flywheel nylon ball bearing - $25. ea PIONEER RT-909 RT909 - Blue Fluorescent "Tape Counter" Readout w/ Circuit board RWX-336 (w/ IC chips; TC5054P, TC4069UBP, TC4011BP & TC5066BP) - $65. PIONEER RT-909 RT909 - Blue Fluorescent "Level Meter" Readout on RWX-338 Circuit Board- $65. SOLD OUT PIONEER RT-909 RT-901 (not compatible with the RT-701 / 707) - Hub spindles (Reel Base assembly with spring spindle / reel lock) -  $109. ea. (Many R2R's are offered for sale by individuals around the world, usually on "on-line" auctions. Most of the R2R's shipped by individuals are not packed adequately and thus sustain damage or are completely destroyed. We even see this when packed by some of the "pros" at the shipping stores. Just because they work there, doesn't mean they are versed in packing fragile, high mass electronics. Reel spindles are the most common part to get damaged or destroyed from amateur / inadequate packaging, and no, double boxing is not the solution!!!. Thus we get many times more request for this part than there are ever parts available. If you see these available and you need them, call quickly as these are some of the first parts to sell due when a machine comes in for salvage.)  - Hubcap / cover for pinch roller with screw and screw bezel (Rollers sold separately) - $35. ea SOLD OUT CLICK HERE NEW FOR PIONEER RT-909 / 901 RXB-325 PINCH ROLLERS    - Rubber Pinch Roller Available - SEE ABOVE, NEAR TOP OF PAGE  - Mic / Line / Output Pots (less knobs) - $40. ea / concentric pair PIONEER RT-909 RT909 - Mic / Line / Output knobs (concentric pairs) - $40 / concentric pair - Pitch Control Pot - $30. - Pitch Control Knob - $30. - Headphone Jack - $30. - Mic Jacks - $35 pair  - 4 Track / Quarter Track Heads (perfect) - $250. for all on the Head cover mounting plate. (Only some single heads currently available) - Single Heads (Erase Head RPB-047 fits 909 / 901, Record Head RPB-064 / RPB-040  fits RT-909 / 901 / 707, Playback Head RPB-065 / RPB-041 fits RT-909 / 901 & RT-707 / 701) - $85. ea. ALSO CHECK OUR RT-707 PARTS LISTINGS FOR HEADS AVAILABILITY AS SOME ARE INTERCHANGEABLE  ---->   (SOLD OUT OF PLAYBACK RPB-065 / RPB-041 HEADS)   Pioneer RT-707 Parts     - Internal circuit boards (RNP-614 fast wind motor control board has issue in that the Rewind motor always turns (less relay and adjustment pots), RWX-341 Fuse circuit board, RWX-340 Audio Board, RWS-078 Transport switch circuit board (less LED's and Momentary Switches), RWG-106 / RWG-105         RNP-614,  transport board, Capstan motor speed control circuit board, RNP-620, RWF-068 / RNP-622 circuit board,  (less pots, switches, large transformers, relays, outputs, start caps, jacks) - $65. ea -Following Internal circuit boards; RWX-337 Sensor Circuit board, RWS-079 (less switches),  - $45. - Blue PC mount, motor tension adjustment micro Pots (from Circuit board RWG-105; 100Ω, 330Ω, 470Ω, 1kΩ) - $18. ea.  - Relay DEC MS2U / RSR-024-0-24DC 6A - $35.  - Pioneer Main Transformer RTT-178 - $95. Capacitors (power supply or Motor Start / Run / any larger electrolytic) - $20 ea. PIONEER RT-909 RT909 - Any internal Solenoid (RXP-075 Brake Solenoid, RXP-071, RXP-070, etc.) - $45. ea. Power Switch (Actual internal switch, not including linkage or silver cap) - $38.50 - Push switches (including Monitor, Bias, EQ, Rec Mode, Reel, Speed, Repeat, Timer). - $35. ea. Silver Push Switch caps (when removable) ( Monitor, Bias, EQ, Rec Mode, Reel, Speed, Repeat, Timer) - $18. ea Transport Buttons (Play, Fast, Rec, Stop, or Pause)- $35. per assembly PIONEER RT-909 RT909 - Tape Tension Arm Assemblies w/ Micro switches (Less front cap, hex bolt and tape roller)- $45. ea As-Is (will need to be disassembled, cleaned and re-lubed) - Tape Tension Front Hub cap / cover - $35. ea. w/ hex bolt -Tape Tension Roller Only - $35 ea.  - Tape Tension brake bands - $35. ea. PIONEER RT-909 RT909 - RCA inputs / outputs - $35. all. Internal Springs - $25 ea.  - Bottom Feet / Skids - $35. ea. SOLD OUT - Cast Frame Sides - $35 ea. PIONEER RT-909 RT909 - Black Case bonnet (Top / Sides sheet metal) - $65. (Cases, covers and side plate / panels, etc. do not include mounting screws, handles etc. as those are sold separately) PIONEER RT-909 RT909 - Upper Back panel (Excellent) - $45. PIONEER RT-909 RT909 - Lower Back panel with info silk screening (Perfect) - $35. PIONEER RT-909 RT909 - Bottom Sheet Metal Panel / Plate (Perfect) - $35. - AC Cord w/ Grommet - $25. For NAB Hub adaptors, click HERE! Other parts not listed quoted individually based mostly on part value and time required to extract. Phone or email for  availability.

NEW LISTING 3/24/07 (Click on above thumbnails to enlarge photos) PIONEER MODEL RT-909 RT909 (#2) REEL TO REEL PARTS PARTING OUT Many parts will also work on the RT-901 RT901 Parting out a clean Pioneer RT-909 Reel-Reel Deck. Everything runs and looks great! This one has some noise emanating from the audio board. Heads in like new condition. Hubs run perfectly true! All motors run fine, fast, smooth and quiet. All transport functions work well. Internal boards will need trim pots adjusted when installed in new deck. Cosmetics like new! We're parting it out as we've had so many requests for parts. Some RT-909 parts may also fit RT-901's, but we have no cross reference info.  Motors, Heads, Circuit Boards, Knobs, Pots, Controls, Switches, Rollers, Spindles, Face Etc. PIONEER RT-909 RT909 - Face Plate, Upper Main (Does not include screws or screw bezels )- Clean and never been rack mounted so screw holes are in "NEW" condition - $75. PIONEER RT-909 RT909 - Lower Face plate with Silk-Screening - Clean and never been rack mounted so screw holes are in "NEW" condition as well as the silk screening - $145. SOLD OUT PIONEER RT-909 RT909 - Capstan Motor - Part # RXM-062- $105. SOLD OUT  Fast Wind / Hub / reel motor right or left Part # RXM-060 - $105. ea Capstan Flywheel (less nylon ball bearing) - $35. ea Capstan Flywheel nylon ball bearing - $25. ea PIONEER RT-909 RT909 - Blue Fluorescent "Tape Counter" Readout w/ Circuit board RWX-336 - $65. PIONEER RT-909 RT909 - Blue Fluorescent "Level Meter" Readout on RWX-338 Circuit Board- $65. SOLD OUT PIONEER RT-909 RT-901 - Hub spindles (Reel Base assembly with spring spindle / reel lock [not compatible with the RT-701 / 707]) - $109. ea. (Many R2R's are offered for sale by individuals around the world, usually on "on-line" auctions. Most of the R2R's shipped by individuals are not packed adequately and thus sustain damage or are completely destroyed. We even see this when packed by some of the "pros" at the shipping stores. Just because they work there, doesn't mean they are versed in packing fragile, high mass electronics. Reel spindles are the most common part to get damaged or destroyed from amateur / inadequate packaging, and no, double boxing is not the solution!!!. Thus we get many times more request for this part than there are ever parts available. If you see these available and you need them, call quickly as these are some of the first parts to sell due when a machine comes in for salvage.)  - Hubcap / cover for pinch roller with screw and screw bezel (Rollers sold separately) - $35. ea SOLD OUT CLICK HERE NEW FOR PIONEER RT-909 / 901 RXB-325 PINCH ROLLERS     - Mic / Line / Output Pots (less knobs) - $40. ea / concentric pair PIONEER RT-909 RT909 - Mic / Line / Output knobs (concentric pairs) - $40 / concentric pair - Pitch Control Knob - $30. - Headphone Jack - $30. - Mic Jacks - $35 pair  - 4 Track / Quarter Track Heads (perfect) - $250. for all on the Head cover mounting plate. (Only some single heads currently available) - Single Heads (Erase Head RPB-047 fits 909 / 901, Record Head RPB-064 / RPB-040  fits RT-909 / 901 / 707, Playback Head RPB-065 / RPB-041 fits RT-909 / 901 & RT-707 / 701) - $85. ea. ALSO CHECK OUR RT-707 PARTS LISTINGS FOR HEADS AVAILABILITY AS SOME ARE INTERCHANGEABLE  ---->   (SOLD OUT OF PLAYBACK RPB-065 / RPB-041 HEADS)   Pioneer RT-707 Parts     - Internal circuit boards (RNP-614 fast wind motor control board has issue in that the Rewind motor always turns (less relay and adjustment pots), RWX-341 Fuse circuit board, RWX-340 Audio Board, RWS-078 Transport switch circuit board (less LED's and Momentary Switches), RWG-106 / RWG-105 / RNP-614,  transport board, Capstan motor speed control circuit board, RNP-620, RWF-068 / RNP-622 circuit board,  (less pots, switches, large transformers, relays, outputs, start caps, jacks) - $65. ea -Following Internal circuit boards; RWX-337 Sensor Circuit board, RWS-079 (less switches),  - $45. - Micro Adjustment Pots - $20. ea.  - Relay DEC MS2U / RSR-024-0-24DC 6A - $35.  - Pioneer Main Transformer RTT-178 - $95. PIONEER RT-909 RT909 - Any internal Solenoid (RXP-075 Brake Solenoid, RXP-071, RXP-070, etc.) - $45. ea. Power Switch (Actual internal switch, not including linkage or silver cap) - $38.50 - Push switches (including Monitor, Bias, EQ, Rec Mode, Reel, Speed, Repeat, Timer). - $35. ea. Silver Push Switch caps (when removable) ( Monitor, Bias, EQ, Rec Mode, Reel, Speed, Repeat, Timer) - $18. ea Transport Buttons (Play, Fast, Rec, Stop, or Pause)- $35. per assembly PIONEER RT-909 RT909 - Tape Tension Arm Assemblies w/ Micro switches (Less front cap, hex bolt and tape roller)- $45. ea As-Is (will need to be disassembled, cleaned and re-lubed) - Tape Tension Front Hub cap / cover - $35. ea. w/ hex bolt -Tape Tension Roller Only - $35 ea.  - Tape Tension brake bands - $35. ea. PIONEER RT-909 RT909 - RCA inputs / outputs - $35. all. Internal Springs - $25 ea.  - Bottom Feet / Skids - $35. ea. SOLD OUT - Cast Frame Sides - $35 ea. PIONEER RT-909 RT909 - Black Case bonnet (Top / Sides sheet metal) - $65. (Cases, covers and side plate / panels, etc. do not include mounting screws, handles etc. as those are sold separately) PIONEER RT-909 RT909 - Upper Back panel (Excellent) - $45. PIONEER RT-909 RT909 - Lower Back panel with info silk screening (Perfect) - $35. PIONEER RT-909 RT909 - Bottom Sheet Metal Panel / Plate (Perfect) - $35. - AC Cord w/ Grommet - $25. For NAB Hub adaptors, click HERE! Other parts not listed quoted individually based mostly on part value and time required to extract. Phone or email for  availability.

CONTACT INFO BELOW


$5 Surcharge on all orders under $20.

 

                                             

    Before calling, PLEASE read the text in orange below.      
No Really...Stop, Alto, Halt, etc.
 BEFORE CALLING (719) 964-7205 
OR EMAILING parts@oaktreevintage.com .

If you DID NOT see your Unit or Part
"SPECIFICALLY"
listed, or the part you are seeking was already marked
"SOLD or SOLD OUT"
then please DO NOT CALL or EMAIL for it.
If you do not see it listed,   we do not have it,    nor do we know when it will come in,    nor do we have a "waiting list" for it,     nor do we know who would have it.
Sorry, but phone traffic for parts we don't have listed or for parts that are already marked "SOLD" is too consuming of time resources.

      If you DO see your part listed, and it appears to be available or you know for a fact that it is a VERIFIED-GOOD substitution from a unit or part that we do show, then by all means, give us a call to verify availability and to place the order.
 We try to keep these pages 99+% updated.
If you don't see the part you are looking for, simply check the web page periodically as we never know what will show up each day. Thanks!!!!!

9:30 AM- ~7:30 PM most days COLORADO / ROCKY MOUNTAIN TIME ZONE

ALSO: When e-mailing be sure to include a RELEVANT TOPIC, ie: Brand / Model number in the SUBJECT LINE. SUBJECT lines left empty, or with SUBJECTS like;
Hello, Hi, "no subject" or similar will automatically be deleted by Anti-Virus / Spam settings.




___________________________________________

Haven't received a response to your email? See FAQ'S

MAILING:
OAK TREE ENTERPRISES
PO. BOX 6182
COLORADO SPRINGS, CO 80934
U.S.A.

Before ordering by postal mail, please phone or email us about the item 
and the details of sending your funds. Thank-you.

   FAQ'S  I    CONDITION RATINGS   |   ORDERING / POLICIES   |   WARRANTIES / RETURNS   |   SHIPPING    |   HOLD / SOLD   |  RESTORATION PROCEDURES  I  LINKS   |  CLIENT LIST 


20% restock fee applies to all returns for refund.
See our "Warranties / Returns" page via the link below for more details.

POLICIES, SPECIFICATIONS, AVAILABILITY, INFORMATION
AND PRICING SUBJECT TO CHANGE  AT ANYTIME  AND WITHOUT PRIOR NOTICE
and changes may not be posted to web immediately. 
Information such as Parts Substitution possibilities, "Circa" dates, original values, etc. are to the best of our knowledge. If you are critically concerned, 
you should do independent research on your own prior to ordering or utilizing this information in any way. Manufacturers also are known to change
part numbers, specs, circuit designs, specs etc within the same model.

Copyright © 1997-2010 Oak Tree Enterprises
All manufacturer and product names are copyrights of their respective owners. 
All photos and text contained within this site are protected and may not be 
reproduced or used elsewhere, in anyway, without including the original credit tags / text. They also must be used / reproduced in their original form and include a complimenting credit to Oak Tree Vintage for their creation. This of course includes using OUR photos and OUR text in YOUR auctions / listings.  All Rights Reserved. Site created with "Front Page" and is likely best viewed with Internet Explorer ™. Will likely work on most other browsers as well.