(CLICK ON THUMBNAIL TO ENLARGE PHOTO)
Replacement Pioneer / Akai / Allied Speaker Plugs
The very hard to find Akai & Pioneer receiver / amplifier to speaker, short proof adaptor plugs / connectors / jacks. If you have an old Early-Mid 1970's Akai, Allied or Pioneer receiver / Amplifier that uses these, and have lost yours or need an additional set - here you go! These receiver / amplifier / speaker plugs were used in the Akai receiver model AA-910, 920, AA-930, 940, AA-960, 970 AA-980, Pioneer Receiver / Amplifier to Speaker plugs for Pioneer receiver and amplifier models QA-800, SA-100, SA-302 & 302R, SA-500, SA-600, SA-700, SA-800, SA-900, SA-1000, SX-300T, SX-400, SX-424, SX-440, SX-525, SX-626, SX-727, SX-770, SX-828, SX-990, SX-1000 1000TD & TW, SX-1500, 1500TD, SX-2500, SX-6000, SX-9000, QX-4000, QX-8000, QX-9000, QX-9900 , Speaker plugs for Allied receiver models 335, 355, 365, 380, 395, 399, 435, 445, 490, 498, 475, 495 and may have been used in other receiver / amplifier models as well.
NO SOLDERING REQUIRED!
Sold in pairs.

 1 pair = $38.50 shipped
2 pairs = $64.50 shipped
3 pairs = $83.50 shipped

 Available for a limited time as they are no longer being manufactured.

Price includes shipping anywhere in the lower 48 states!

Other locales on the planet can be calculated.  
 

Domestic US Customers

PRICE INCLUDES SHIPPING: Replacement Pioneer / Akai / Allied Speaker Plugs 1 PAIR Your Price $38.50 2 PAIRS Your Price $64.50 3 PAIRS Your Price $83.50

IF YOU PREFER TO PLACE YOUR ORDER BY PHONE,
PLEASE CALL US AT:

719-964-7205

 

JUST FYI FOR FOLKS LOOKING FOR
 PIONEER
CS-99, CS-88a, CS-77a & 66G
MODEL SPEAKERS.
Pioneer, for some reason used foam surrounds on the tweeters of these models, CS-66G, CS-77, CS-88a & CS-99. After 20+ years, it will be difficult to find a pair that still has the foam intact (as foam surrounds generally have a useable lifespan of 10-15 years, depending on the environment they have spent the majority of their lives in). 
Almost 100% of the models we have seen have their tweeter foam rotted. WE have searched high and low for a 16 ohm replacement for the CS-88a, or an 8 ohm for the 77a, with no success.

However, you can now replace the foam your self.
NEW INFORMATION.
ORANGE COUNTY SPEAKERS NOW HAS A REPLACEMENT SURROUND THAT WILL WORK ON THIS
IT WILL NEED TO BE TRIMMED SLIGHTLY ON THE OUTSIDE, BUT WORKS WELL.
THE PART NUMBER IS:
#1-023
THEIR WEB SITE IS  www.speakerrepair.com  

(This applies only to Pioneer CS-99, CS-88a, 77a & 66G tweeters).

   

    The tweeter just to the left is from the CS-77a. Looks good, but surround is rotted.


A visibly fine surround, is still bad and will visibly deteriorate after a few songs are played on them. We see these at on-line auctions often, and in every case the speakers either still have their rotted originals or a replacement tweeter, of some-sort installed. Due to the rarity of 16 ohm tweeters, we have to assume that the replacement tweeters the owners / sellers have installed are of incorrect impedance, which at the least, effects high-end efficiency (volume) & at worst can create load issues for whatever amplifier they are connected to. All this while using the word "Mint" or some similar adjective to list / describe the speakers. 
Again this is only prevalent in CS-77a, CS-88a and CS-99. It is not a factor with CS-77, CS-88, CS-99a, CS-33a, 66a or 901a's.

PS. We also see a similar problem with many other manufacturers' speakers like the Bose 301, 501, 601 & 901 speakers from 15+ years ago, except for the earliest versions of their speakers which used cloth surrounds. 

Any manufacturers' speaker utilizing foam surrounds (common from typically 1980 thru present) that is over 10 years old should be suspect, but the above mentioned models are almost a given.

PSS. Even though a speakers foam surrounds may "look" fine, they probably are not! Vintage speakers posted for sale by individuals & at auctions / yard sales have commonly not been in use for many years (other wise they probably wouldn't be for sale). In many cases, once you start playing them more than a couple minutes, you can watch the foam disintegrate right before your eyes, just by playing 2 or 3 songs at above average volume levels.

Just FYI while you're out looking.

   Pioneer

   Pioneer

   Pioneer


 

   Pioneer


 

(See also HPM-40 / 40U / 40M / HPM-60 / 60M / 60U / HPM-100 / 100U / HPM-110X, CS-T5 / CST5)

(While the super tweeters from the HPM-40, HPM-60 and HPM-100 appear to be interchangeable, the terminals are spaced differently on the two and you may need to modify the wire access hole to fit. The "A" version has a terminal spread of 1 7/8" / ~45mm. The "B" version has a terminal spread of ~3/4" / ~20mm. The "A" version also has a thicker body at ~11mm. The "B" version has a body that is approx 7mm thick.

              

HP-015A-1                                                                                       HP-015B-1

PIONEER HPM SUPER TWEETERS

          

(Click on above thumbnails to enlarge photos)
 

Below is the parts listing for the HPM-60, and not necessarily for the HPM-60/U HPM-60M (The "U" / "M" suffix designates "military market" products which were generally rated at twice the power handling of the domestic US market units). Most parts are different. Please read and compare the part numbers carefully prior to calling in for an order.

 

(See also HPM-40 / 40U / 40M / HPM-60 / 60M / 60U / HPM-100 / 100U / HPM-110X, CS-T5 / CST5)

(While the super tweeters from the HPM-40, HPM-60 and HPM-100 appear to be interchangeable, the terminals are spaced differently on the two and you may need to modify the wire access hole to fit. The "A" version has a terminal spread of 1 7/8" / ~45mm. The "B" version has a terminal spread of ~3/4" / ~20mm. The "A" version also has a thicker body at ~11mm. The "B" version has a body that is approx 7mm thick.

              

HP-015A-1                                                                                       HP-015B-1

PIONEER HPM SUPER TWEETERS

          

(Click on above thumbnails to enlarge photos)
 

Below is the parts listing for the HPM-60/U2 / M, and not necessarily for the HPM-60. (The "U" / "M" suffix designates "military market" products which were generally rated at twice the power handling of the domestic US market units). Most parts are different. Please read and compare the part numbers carefully prior to calling in for an order.

 

   Pioneer

(See also HPM-40 / 40U / 40M / HPM-60 / 60M / 60U / HPM-100 / 100U / HPM-110X, CS-T5 / CST5)

See Above Notes also.
 

(While the super tweeters from the HPM-40, HPM-60 and HPM-100 appear to be interchangeable, the terminals are spaced differently on the two and you may need to modify the wire access hole to fit. The "A" version has a terminal spread of 1 7/8" / ~45mm. The "B" version has a terminal spread of ~3/4" / ~20mm. The "A" version also has a thicker body at ~11mm. The "B" version has a body that is approx 7mm thick.

              

HP-015A-1                                                                                       HP-015B-1

PIONEER HPM SUPER TWEETERS

          

(Click on above thumbnails to enlarge photos)

 

(See also HPM-40 / HPM-60 / HPM-100 )

(While the super tweeters from the HPM-40, HPM-60 and HPM-100 appear to be interchangeable, the terminals are spaced differently on the two and you may need to modify the wire access hole to fit. The "A" version has a terminal spread of 1 7/8" / ~45mm. The "B" version has a terminal spread of ~3/4" / ~20mm. The "A" version also has a thicker body at ~11mm. The "B" version has a body that is approx 7mm thick.

              

HP-015A-1                                                                                       HP-015B-1

PIONEER HPM SUPER TWEETERS

          

(Click on above thumbnails to enlarge photos)
 

(CLICK ON THUMBNAIL TO ENLARGE PHOTO)
Replacement Pioneer / Akai / Allied Speaker Plugs
The very hard to find Akai & Pioneer receiver / amplifier to speaker, short proof adaptor plugs / connectors / jacks. If you have an old Early-Mid 1970's Akai, Allied or Pioneer receiver / Amplifier that uses these, and have lost yours or need an additional set - here you go! These receiver / amplifier / speaker plugs were used in the Akai receiver model AA-910, 920, AA-930, 940, AA-960, 970 AA-980, Pioneer Receiver / Amplifier to Speaker plugs for Pioneer receiver and amplifier models QA-800, SA-100, SA-302 & 302R, SA-500, SA-600, SA-700, SA-800, SA-900, SA-1000, SX-300T, SX-400, SX-424, SX-440, SX-525, SX-626, SX-727, SX-770, SX-828, SX-990, SX-1000 1000TD & TW, SX-1500, 1500TD, SX-2500, SX-6000, SX-9000, QX-4000, QX-8000, QX-9000, QX-9900 , Speaker plugs for Allied receiver models 335, 355, 365, 380, 395, 399, 435, 445, 490, 498, 475, 495 and may have been used in other receiver / amplifier models as well. Sold in pairs.

 1 pair = $38.50 shipped
2 pairs = $64.50 shipped
3 pairs = $83.50 shipped

 Available for a limited time as they are no longer being manufactured.

Price includes shipping anywhere in the lower 48 states!

Other locales on the planet can be calculated.  
 

Domestic US Customers

PRICE INCLUDES SHIPPING: Replacement Pioneer / Akai / Allied Speaker Plugs 1 PAIR Your Price $38.50 2 PAIRS Your Price $64.50 3 PAIRS Your Price $83.50

IF YOU PREFER TO PLACE YOUR ORDER BY PHONE,
PLEASE CALL US AT:

719-964-7205