Replacement Pioneer SR, SG, Switch.

Replacement Switch for broken bad Pioneer RG-2, SR-303, SG-9500, SG-9800 Switches- Tape monitor Processor Attenuator Attenuators
(4-pole switch will also work for Sansui 7070, 8080, 9090 DB receiver Audio Mute Switch) Replacement for most Pioneer ASG-212, ASG-213, ASG-313, ASG-214, ASG-316 and others.

(Click on above thumbnails to enlarge photos. Color may vary)
NEW REPLACEMENT SWITCHES FOR
PIONEER SG / SR / RG UNITS
AND OTHERS
If the locking push Tape monitor, Processor, Attenuator or other switch on your Pioneer RG-2, RG2, RG-9, RG9, RG-60, RG60, SG-9, SG9, SG-300, SG300, SG-540, SG540, SG-550, SG550, SG-9500, SG9500, SG-9800, SG9800, SR-9, SR9, SR-60, SR60, SR-303, SR303, ADC, BSR, SS-110, SS-110-IC, SS110, SS110IC,
Pioneer EQ's, Reverbs, Dynamic Processors is not staying in, or will not lock, then here's the
fix for you. May also fit other units. The original switches had / have almost a 100% failure
rate after a few years. If yours is not broken yet, it will fail and probably soon.

Failure is due
to a plastic locking mechanism that is many years beyond it's designed lifespan. The plastic part that fails,
is less than a mm thick, has a metal pin catching on it and is 25+ years old. Almost every time we bench
one of the above listed units, the original switch lock will fail after being depressed a few more times. Even if the lock functioned
when we purchased the unit we know it will either fail on us in restoration or on the buyer of the unit.

These switches will replace Tape Monitor, Attenuator, Processor
and other push-in / locking switches on vintage Pioneer Gear. We have both
12-Pin (4-pole, 6 pins per side) and 18-pin (6-pole, 9 pins per side) switches.
They are a simple install for most electronic techs. Includes basic instructions.
12-Pin (4-pole, 6 pins per side) - $19.99 ea.

18-pin (6-pole, 9 pins per side) - $19.99 ea.
Add $6.50 Shipping to total
regardless of quantity of switches ordered.
$5.00 off for each additional switch ordered after 1st switch.

(4-pole / 6 pin Will also work for Sansui 7070, 8080, 9090 DB Audio Mute Switch. Will also work for ADC / BSR SS-110 IC Equalizer "Tape Monitor". May work on other ADC / BSR EQ's as well. Also fits Yamaha CR-1020 receivers)

WARNING: Electronic equipment carries dangerous and potentially lethal electrical currents. You should never open any electronic unit without proper knowledge of electronics and the hazards of electricity!
Any repair / restoration should be undertaken ONLY by a QUALIFIED ELECTRONICS TECHNICIAN!

FOR PARTS NOT SHOWN ON THE PAGE ABOVE, CLICK HERE.

20% restock fee applies to all returns for refund.

WAIT, before you email or phone
PLEASE READ THIS:

ALSO: When e-mailing be sure to include a RELEVANT TOPIC, ie: Brand / Model number
in the SUBJECT LINE. SUBJECT lines left empty, or with SUBJECTS like;
Hello, Hi or similar will automatically be deleted by Anti-Virus / Spam settings.
(Subject lines left empty show up as "No Subject" and are deleted automatically
by our anti-spam settings"

U.S.A.
( Please see / read the "red" paragraphs above prior to hitting this email link or calling)

ORDERING BY
E-MAIL:
parts@oaktreevintage.com

OR
ORDERING BY PHONE :
(719) 964-7205

9:30 AM- ~7:30 PM most days COLORADO / ROCKY MOUNTAIN TIME ZONE

_____________________

PLEASE DO NOT SEND PHOTO FILES
WITHOUT PRIOR APPROVAL. THANK-YOU.

___________________________________________

Haven't received a response to your email? See FAQ'S

MAILING:
OAK TREE ENTERPRISES
PO. BOX 6182
COLORADO SPRINGS, CO 80934
U.S.A.

Before ordering by postal mail, please phone or email us about the item
and the details of sending your funds. Thank-you.

FAQ'S I CONDITION RATINGS | ORDERING / POLICIES | WARRANTIES / RETURNS | SHIPPING | HOLD / SOLD | RESTORATION PROCEDURES I LINKS | CLIENT LIST

20% restock fee applies to all returns for refund.
See our "Warranties / Returns" page via the link below for more details.
$5 Surcharge on all orders under $20.

POLICIES, SPECIFICATIONS, AVAILABILITY, INFORMATION AND PRICING SUBJECT TO CHANGE AT ANYTIME AND WITHOUT PRIOR NOTICE
and changes may not be posted to web immediately.
Information such as Parts Substitution possibilities, "Circa" dates, original values, etc. are to the best of our knowledge. If you are critically concerned,
you should do independent research on your own prior to ordering or utilizing this information in any way. Manufacturers also are known to change
part numbers, specs, circuit designs, specs etc within the same model.

Copyright � 1997-2010 Oak Tree Enterprises
All manufacturer and product names are copyrights of their respective owners.
All photos and text contained within this site are protected and may not be
reproduced or used elsewhere, in anyway, without including the original credit tags / text. They also must be used / reproduced in their original form and include a complimenting credit to Oak Tree Vintage for their creation. This of course includes using OUR photos and OUR text in YOUR auctions / listings. All Rights Reserved. Site created with "Front Page" and is likely best viewed with Internet Explorer �. Will likely work on most other browsers as well.